These compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route 22884-10-2, its application will become more common.
Some common heterocyclic compound, 22884-10-2, name is 2-(1H-Imidazol-1-yl)acetic acid, molecular formula is C5H6N2O2, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route. 22884-10-2
Example 1; [0022] An oven-dried 250 ml_ 4-neck RB flask was fitted with a mechanic stirrer, K-thermocouple, condenser, nitrogen inlet and outlet and two 1/8 inch polytetrafluoroethylene (PTFE) feeding lines. The system was flushed with nitrogen for 30 minutes. Under nitrogen protection, imidazoIe-1-ylacetic acid (15.97 g, 0.13 mole), sulfolane (70 ml_) and phosphorous acid (2.67 g, 0.033 mol) were charged to the RB flask. The reaction mixture was mixed at 210 RPM and heated to 600C. PCI3 (9.18 g, 0.067mol) was added slowly (1.3 mL/mn) via a masterflex tubing pump. Five minutes were allowed for mixing. Alternately fed were 26 wt% phosphorous acid sulfolane solution (30.7 g, 10.23 g each addition at 1.6 mL/min) and PCI3 (27.5 g, 9.18 g each portion at 1.3 mL/min). Three to five minutes of mixing were allowed between additions. The addition took 1 hr 3 min and temperature was maintained between 600C and 670C. After addition was complete, the temperature of the reaction mixture was raised to 800C and was held at this temperature for 4 hours. Then the temperature of the reaction mixture was raised to 880C and held for 30 minutes. Ambient temperature water (50 g) was added in to quench the reaction. The solution was refluxed for 3 hrs . temperature, the product was vacuum-filtered and rinsed with 38 g of acetone. Zoledronic acid was obtained as a white crystalline solid (24.1 g, 95.3wt% purity by quantitative NMR, 65% yield). Example 2; [0023] An oven-dried 250 mL 4-neck RB flask was fitted with a mechanic stirrer, K-thermocouple, condenser, nitrogen inlet and outlet and two 1/8 inch PTFE feeding lines. The system was flushed with nitrogen for 30 minutes. Under nitrogen protection, imidazole-1-ylacetic acid (15.97 g, 0.13 mole), sulfolane (70 mL) and phosphorous acid (2.67 g, 0.033 mol) were charged to the RB flask. The reaction mixture was mixed at 300 RPM and heated to 600C. PCI3 (9.18 g, 0.067mol) was added in slowly (1.3 mL/min) via a masterflex tubing pump. Five minutes were allowed for mixing. Alternately fed were 26 wt% phosphorous acid sulfolane solution (30.7 g, 10.23 g each addition at 1.6 mL/min) and PCI3 (27.5 g, 9.18 g each portion at 1.3 mL/min. Three to five minutes of mixing were allowed between additions. The addition took 1 hr 6 min and temperature was maintained between 54 and 64C. After addition was complete, the temperature of the reaction mixture was raised to 800C and held for 4 hours. Then the temperature of the reaction mixture was raised to 880C and held for 30 minutes. This slurry was transferred via 3/8″ PTFE tubing using nitrogen pressure into 100 mL of pre-heated (80C) water under mixing. The resultant water solution was heated to refluxing and held at that temperature for 4 hr. It was then slowly cooled to room temperature then to 1-2C and held for 1.5 hr at this temperature. The product was collected via vacuum filtration. The cake was rinsed with acetone (20 g) and zoledronic acid was obtained as a white crystalline solid (19.1 g, 98.3 wt% purity by quantitative NMR, 53% yield). Example 3; [0024] An oven-dried 250 mL 4-neck RB flask was fitted with a mechanic stirrer, K-thermocouple, condenser, nitrogen inlet and outlet and two 1/8 inch PTFE feeding lines. The system was flushed with nitrogen for 30 minutes. Under nitrogen protection, imidazole-1-ylacetic acid (15.9 g, 0.13 mole), sulfolane (70 mL) and phosphorous acid (2.67 g, 0.033 mol) were charged to the RB flask. The reaction mixture was mixed and heated to 6O0C. PCI3 (36.7 g, 0.267 mol) and phosphorous acid (8.0 g, 0.098 mol) in – . mL/min respectively. Reaction temperature remained between 6O0C and 67C during feeding, After addition of PCI3 and phosphorous acid, the reaction slurry was heated to 800C and held at that temperature for 4 hours. This slurry was then transferred via 3/8″ PTFE tubing using nitrogen pressure into 50 m._ of pre-heated (8O0C) water under mixing. The resultant water solution was heated to refluxing and held at that temperature for 4 hr. It was then slowly cooled to 48-500C. Acetone (200 ml_) was added in slowly and then it was cooled to 1-2C and held for 2 hr at this temperature. The product was collected via vacuum filtration. The cake was rinsed with acetone (35 g) and zoledronic acid was obtained as a white crystalline solid (22.1 g, 98.6 wt% purity by quantitative NMR, 61 % yield). Example 4; [0025] A 2.5 L resin-kettle was fitted with a mechanic stirrer, K-thermocouple, condenser, nitrogen inlet and outlet, two 1/8 inch PTFE tubing as PCI3 and phosphorous acid sulfolane solution feeding lines. The system was dried under a stream of nitrogen. Under nitrogen, imidazoleacetic acid (79.92 g, 0.63 mol), phosphorous acid (13.90 g, 0.17 mol) and sulfolane (350 ml_) were added to the resin-kettle and mixed at 200 RPM. The mixture was heated to 62C then PCI3 (36.7 g, 0.267 mol) was added in slowly (1.3 mL/min) using a masterflex tubing pump. The slurry was mixed for 5 minutes. Phosphoro…
These compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route 22884-10-2, its application will become more common.
Reference:
Patent; ALBEMARLE CORPORATION; WO2008/157050; (2008); A1;,
Imidazole – Wikipedia,
Imidazole | C3H4N2 – PubChem